AE-ISP-ST7 – DIP28/BH10 specialized adapter for in system programming of ST7 and STM8 microcontrollers

$90.00 each


Supported Devices:
Click the device programmer model below to get an appropriate list of the devices supported by this programmer with this adapter:
Adapter Connection Table

DIP28/BH10 specialized adapter for in system programming of ST7 and STM8 microcontrollers.

Connections to the target devices:

AE-ISP-ST7 connection for the ADAM2xx devices


Recommended connection:

AE-ISP-ST7 connection for the ADAM2xx devices

Powering the target device:
The target gets power from the programmer (Vdd). This is possible only if the target does not consume too much energy. A capacity of the target power circuitry should not exceed 50 uF.
NOTE! It is strictly prohibited to power the target from both the programmer and built-in or external power supply simultaneously.

Isolating resistors:
Purpose of the R1,R2 resistors is to isolate the programmed chip from rest of target system. Recommended value of resistors R1,R2 is 2k or more. You can also use jumpers instead of the resistors.

ISP characteristics:
1. Programmer''s output capability:
1.1 Vcc - 80 mA;
1.2 Vpp - 50 mA;
1.3 logical pins - 5 mA.
2. The cable length should be less then one foot.

Adapter Connection Table:


AE-ISP-ST7 connection for the ST7 devices


Recommended connection:

AE-ISP-ST7 connection for the ST7 devices

Powering the target device:
There are two alternative options for powering the targets:
1. The target gets power from the programmer (Vdd). This is possible only if the target does not consume too much energy. A capacity of the target power circuitry should not exceed 50 uF.
2. The target gets power from a built-in or external power supply. In this case the power output from the programmer should not be connected with the target. The target system should be tolerant to applying logical signals with the voltage levels exceeding the voltages on the target.
NOTE! It is strictly prohibited to power the target from both the programmer and built-in or external power supply simultaneously.

Isolating resistors:
Purpose of the R1..R4 resistors is to isolate the programmed chip from rest of target system. Recommended value of resistors R1..R4 is 2k or more. You can also use jumpers instead of the resistors.

ISP characteristics:
1. Programmer''s output capability:
1.1 Vcc - 80 mA;
1.2 Vpp - 50 mA;
1.3 logical pins - 5 mA.
2. The cable length should be less then one foot.

Adapter Connection Table:


AE-ISP-ST7 connection for the STM8 devices


Recommended connection:

AE-ISP-ST7 connection for the STM8 devices

Powering the target device:
There are two alternative options for powering the targets:
1. The target gets power from the programmer (Vdd). This is possible only if the target does not consume too much energy. A capacity of the target power circuitry should not exceed 50 uF.
2. The target gets power from a built-in or external power supply. In this case the power output from the programmer should not be connected with the target. The target system should be tolerant to applying logical signals with the voltage levels exceeding the voltages on the target.
NOTE! It is strictly prohibited to power the target from both the programmer and built-in or external power supply simultaneously.

Isolating resistors:
Purpose of the R1,R2 resistors is to isolate the programmed chip from rest of target system. Recommended value of resistors R1,R2 is 2k or more. You can also use jumpers instead of the resistors.

ISP characteristics:
1. Programmer''s output capability:
1.1 Vcc - 80 mA;
1.2 Vpp - 50 mA;
1.3 logical pins - 5 mA.
2. The cable length should be less then one foot.

Adapter Connection Table:


AE-ISP-ST7 connection for the TI CC25xx devices


Recommended connection:

AE-ISP-ST7 connection for the TI CC25xx  devices

Powering the target device:
There are two alternative options for powering the targets:
1. The target gets power from the programmer (Vdd). This is possible only if the target does not consume too much energy. A capacity of the target power circuitry should not exceed 50 uF.
2. The target gets power from a built-in or external power supply. In this case the power output from the programmer should not be connected with the target. The target system should be tolerant to applying logical signals with the voltage levels exceeding the voltages on the target.
NOTE! It is strictly prohibited to power the target from both the programmer and built-in or external power supply simultaneously.

Isolating resistors:
Purpose of the R1,R2 resistors is to isolate the programmed chip from rest of target system. Recommended value of resistors R1,R2 is 2k or more. You can also use jumpers instead of the resistors.

ISP characteristics:
1. Programmer''s output capability:
1.1 Vcc - 80 mA;
1.2 Vpp - 50 mA;
1.3 logical pins - 5 mA.
2. The cable length should be less then one foot.

Adapter Connection Table:


Adapter connection table: